ECHO Tec. Watermaker

Options and Accessories - DC Series

 

 

Boost pump, submersible (System DML-200/240/260) - 160

If the high-pressure pump is installed less than 2 feet below the waterline or an additional 5 micron pre-filter is added, the installation of an optional boost pump is recommended. The boost pump also helps to prime the system after pre-filter changes and increases the lifetime of the pre-filter. Draws only 1 amp at 12 VDC (½ amp at 24 VDC).

1 Magnetic drive (no seal/no leak - no corroding stainless shaft) submersible Boost Pump, hydraulic/magnetic circuit breaker for control panel, AISI 316 stainless steel pump 5/8" intake hose barb, 1/2" outlet hose barb, 4 feet / 1.2 meter 5/8" wire reinforced intake (suction) hose, 10 feet / 3 meter 1/2" braided feed hose




 

Boost pump (Systems DML-430/780) -  235

If the high-pressure pump is installed less than 2 feet below the waterline or an additional 5 micron pre-filter is added, the installation of an optional boost pump is recommended. The boost pump also helps to prime the system after pre-filter changes and increases the lifetime of the pre-filter. Draws only 3.5 amp at 12 VDC (1.8 amp at 24 VDC).

1 Magnetic drive (no seal/no leak - no corroding stainless shaft) Boost pump hydraulic/magnetic circuit breaker for control panel, 5/8" intake hose barb, 5/8" outlet hose barb, 4 feet / 1.2 meter 5/8" wire reinforced intake (suction) hose, 10 feet / 3 meter 5/8" braided feed hose.

 


 


5 Micron Pre-filter housing - Free of charge


The additional 5 micron pre-filter is only recommended in connection
with the optional boost pump.

1 Filter housing, 1 pre-filter cartridge, 1 bracket, 1 3/4" NPT nipple


Low pressure gauge - 68

The low pressure gauge indicates when the pre-filters have to be changed or the through-hull becomes clogged (barnacles etc.).

Low pressure gauge (316SS housing / Monel bourdon tube) -30 +60PSI, ¼”NPT thread in filter housing, 316SS bracket with cutout for gauge.


Fresh water flush kit -98

The fresh water flush kit enables you to store your watermaker for up to 10 days without the use of chemicals (biocide). The fresh water flush storage can be repeated every 10 days.

1 Filter housing, 1 active carbon cartridge, 316 SS bracket, 8 screws, shut off valve, 2 hose barb connectors, Nylon tee, 10 ft braided hose, 316SS hose clamps.


Custom DUPLEX Upgrade - 262

DUPLEX 1.4462 (similar to 2205) is more costly and more difficult to form and machine but achieves almost twice the corrosion resistance of 316 stainless steel. DUPLEX has been successfully used for all high pressure fittings and pressure regulators of ECHOTec commercial desalination systems for the past 10 years. The custom Duplex upgrade is now available as an option for yacht watermakers.

The Duplex package comes with a lifetime warranty (If for any reason, a DUPLEX regulator or fitting ever fails, we replace it. Period).


 


Maintenance Kit - ₤ 115


10 Pre-filters, 5 and/or 20 micron (2 ½” x 10”)
  1 Spare sea strainer screen
  2 Active carbon filters (fresh water flush)
  1 Ltr. High-pressure pump oil


 
Extended Maintenance Kit - ₤
98 

  2 DC motor brushes
  1 Acid cleaning compound
  1 Alkaline cleaning compound
  2 Storage compounds (Biocide)
  1 Complete spare seal and O ring kit (except high pressure pump)

 
Consumables         ₤
   
5 micron pre-filter cartridge     6.20
20 micron pre-filter cartridge     6.20
Active carbon cartridge   11.80
pH neutralizer / mineral cartridge   42.70
Sea strainer screen   13.10
High rejection / high flow membrane element 40” 176.00
Biocide / Storage compound     6.20
Alkaline cleaner     9.30
Acid cleaner     9.30
DC motor brushes (pair)   30.30
Timing Belt   12.50
High Pressure Pump valve kit   84.10
High Pressure pump seal kit (Water and Oil) 102.80
   

 
Order by phone or e-mail.     Wire transfer or Visa/MasterCard accepted.
parts@echo-marine.com     Tel: + 868 634 20 27
 

Back to DC Watermakers